PRECAUTIONS:
• Floor temperature must be between 10 − 30 °C.
• Floor moisture content must be between 9 − 14% as per
Australian Standard. A moisture meter is recomme
nded to indicate conditions.
• In hot and dry climates slightly reduce exposure to
direct air to prevent rapid and uneven drying.
• Do not cover the surface with non-porous protective
materials as the curing time can take more than 7 days
DIRECTIONS FOR USE:
Reference is made to the Australian Standard Code
AS 4786.2-2005: Timber Flooring – Sanding and Finishing.
NEW OR FRESHLY SANDED TIMBER FLOORS:
Sand timber floor to a fine finish using accepted procedures.
Machine sand the surface to remove old treatments and
impurities in the wood. Use a coarse sanding paper and
sand the floor to an even and smooth finish. Make a second
cut with 100−120 grit sand paper and then fine sand with
120−150 grit sand paper. This finishing will reduce the
amount of grain raise.
Vacuum thoroughly and tack the floor with a mineral
turps dampened cloth before applying TUNG OIL SEAL
Do not forget to remove dust from skirting, windowsills,
radiators and other exposed areas.
APPLICATION OF SEALER/ PRIMER
All timber surfaces should be clean and properly prepared.
All application tools must be clean and free of contamination.
Apply first coat of TUNG OIL SEAL at the recommended rate
using selected application method.
Cut in edges using a paint brush or paint pad.
Smooth the seal in line with the timber grain and lay of the floor.
Ensure an even coating is obtained without puddles and misses.
CUT BACK OF WOOD FIBRE:
Application of a sealer may raise the grain of the
timber creating a rough surface which needs to be smoothed.
Lightly sand the first coat TUNG OIL SEAL
with a worn 150 grit screen disc. Pass quickly over
the surface to avoid burnishing.
Vacuum thoroughly and tack the floor with a water-dampened cloth.
APPLICATION OF FINISH:
The Second and subsequent coats of TUNG OIL SEAL will take longer
to dry, up to 8 hours. Allow floor at least 48 hours before
opening to light traffic. Do not cover the surface with
non-porous protective materials as full cure can take more
than 7 days.
INTERCOAT ABRASION:
Abrading between coats of TUNG OIL SEAL is not required
for adhesion unless more than 24 hours have elapsed or any
grain raise is still evident, in which case, lightly cut
the surface back with a worn 150 grit screen disc. However,
for the smoothest floor results free of impediments, lightly
abrade prior to the final finish coat with a De nibbing pad.
REFURBISHING PREVIOUSLY SEALED FLOORS:
The floor is to be swept clean of all debris and dirt.
Ensure all contaminants are removed by thoroughly scrubbing
the entire floor surface with a solution of TIMBER PRECLEAN
following label instructions. Using a wet & dry vacuum
or mop & bucket, pick up slurry then thoroughly rinse with
clean water. If the floor has been previously treated with
wax or polish this must be removed by chemical stripping.
Use Peerless Jal ALL PURPOSE STRIPPING EMULSION
following label instructions. Exposure to water should be
kept to a minimum during the scrubbing or stripping processes.
Allow the floor to dry completely.
Cut back previously sealed floors with a 100–120 grit screen
disc to remove raised wood fibre, surface imperfections and
provide an adequate surface for resealing.
Vacuum thoroughly and tack the floor with a mineral
turps dampened cloth. A small test area using TUNG OIL
SEAL(1m2) may be tried first to check compatibility.
CARE AND MAINTENANCE:
Regular and correct maintenance will extend the life
of your timber floor and present it at its best.
• Attach protective pads to furniture legs.
• Use matting at all external entries to contain and
prevent dirt and grit from entering.
• Sweep daily with an electrostatic mop.
• Spot mop spillages as they occur.
• Damp mop when required.
• Use VERSADET neutral floor cleaner following label
instructions.
• D o not over wet your timber floor.
• Do not expose your timber floor to heavy traffic until
full curing of the seal/finish is effected.
At periodic intervals your timber floor will require
treatment by way of additional coats of timber seal/finish.
We recommend that you thoroughly inspect your floor regularly
and schedule a re-treatment prior to major restoration or full
sanding being required. This will provide a lifetime of use from
your timber floor.
MAINTAINING THE FLOOR FINISH
Once TUNG OIL SEAL is fully cured the recommend mai
ntenance in heavy wear areas is to use Peerless JAL Gemini
floor polish to protect and extend the life of TUNG OIL SEAL.
This should be applied following the manufacturers
instructions.
SAFETY
Swallowed: Do not induce vomiting. Give a glass of water and
contact doctor or the Poisonous Information Centre on
(Australia 13 11 26 or New Zealand 0800764 766).
Eyes: If in eyes, hold eyelids open and irrigate with water
for at least 15 minutes. See a doctor if affects persist.
Skin: Remove contaminated clothing; wash affected area with
soap and water.
Inhalation: If risk of inhalation exists, wear organic vapour/
particulate respirator meeting the requirements
of AS/NZS 1715/6
